Anchor Rings | Anchor Retrieval
Home > Docking & Anchoring > Anchor Rings & Pullers > Ironwood Pacific Anchor Ring Stainless Anchor Retriever >

Ironwood Pacific Anchor Ring Stainless Anchor Retriever

Ironwood Pacific Anchor Ring Stainless Anchor Retriever
Ironwood Pacific Anchor Ring Stainless Anchor Retriever
Ironwood Pacific Anchor Ring Stainless Anchor Retriever - 002.AnchorRing.Parent
Stainless Steel Anchor ring manufactured by Ironwood Pacific in the USA
Ironwood Pacific anchor Ring with tether and clip
Ironwood anchor Ball with stainless steel ring

An anchor ring eliminates hauling your anchor up by hand or needing a winch.

  • Will float anchors up to 80 lbs. 
  • Use with anchor lines rigged with more than 15' of chain
  • Quickly clips to anchor line 
  • Easy, affordable solution for anchor retrieval
  • Lifetime warranty

In Stock
Ships in 1-2 Bus. Days

Item # Description Buoy Size Buoyancy Options Sale Price Quantity
Anchor Ring No buoy No buoy
Anchor Ring Tether & Clip No buoy No buoy
Anchor Ring with Standard Buoy 11.5" 30 lbs

Anchor Ring with Large Buoy 15.5" 60 lbs

Anchor Ring with Jumbo Buoy 18.5" 80 lbs


Anchor Ring Anchor Retrieval

Anchor Ring anchor retrieval is designed for offshore applications where longer lengths of anchor chain are common.  Our Anchor Ring has been specifically engineered to offer exceptional performance and value to boaters.  Once you have used our Anchor Ring anchor retrieval, you will never want to go back to hauling your anchor by hand again.

Key Features of Anchor Ring Anchor Retrieval

  • Can lift up to 80 lb anchor systems, depending on the capacity of the buoy
  • Stainless steel ring and shackle
  • Designed for anchor lines rigged with more than 15 feet of chain
  • Easy to use - just slip over your anchor line when ready to raise anchor
  • Can be used with any size buoy
  • Available in 2 models
    • Anchor Ring Standard is constructed from 1/4" stainless steel
    • Anchor Ring Heavy-duty is constructed from 5/16" stainless steel
  • Lifetime warranty 
  • Made in the USA

Anchor Ring Buoy Options

 Buoy Size
 Buoy Diameter
 Lifting Capacity
 Color Options
 Standard Buoy
 11.5" 30 lbs.
 Red, Yellow
 Large Buoy
 15.5" 60 lbs.
 Red, Yellow
 Jumbo Buoy
 18.5" 80 lbs.
 Red, Yellow

How does Anchor Ring anchor retrieval work?

 1.  Slip the Anchor Ring over the anchor line.  Attach the shackle- buoy assembly.  Be sure to snap the shackle through both eyes of the ring.  Toss the buoy into the water allowing the ring to slide down the line.  2.  Motor your boat at a 30 degree angle off of your anchor point, taking care to keep the anchor line clear of the prop.  Proceed slowly (roughly 5 knots) until the anchor is released from the bottom.  Then increase speed slightly.  3.  The anchor line will slide through the ring as the buoy floats on the surface.  Once the anchor has reached the surface, shift into neutral and pull in the slack anchor line and anchor.  The anchor chain will counterbalance the anchor and hold the anchor at the surface.
 anchor ring anchor retrieval  anchor ring anchor retrieval illustration  anchor ring anchor retrieval in action

Watch anchor retrieval in action

Watch the AnchorLift anchor puller in action

How To Inflate a Polyform Buoy by Ironwood Pacific Outdoors - Videos

Today, we are going to show you how to properly inflate a Polyform buoy. First, use a flathead screwdriver to unscrew the cap from the air valve. You may use either an air compressor or a Polyform Hand Pump to inflate the buoy. If using an air compressor, set the compressor to 30 psi or less, place the compressor nozzle over the valve airway of the buoy, and inflate up to a maximum of 2 psi. No special attachment or tip is needed. When using the hand pump, simply insert the nozzle into the air valve and pump until full. The valve flap may not fully open when using a Polyform Hand Pump; therefore, you may need to insert a blunt object--such as a small screwdriver or awl--prior to inflation. After inflation, you should be able to make a quarter-inch indentations with your fingers. However, the buoy should still be fairly firm. Then, use your screwdriver to tighten the cap back into the valve.

How To Clean a Polyform Inflatable Buoy - Videos

Clean Polyform fenders look good, and they help keep your boat clean. The simplest way to clean a Polyform fender is to try using soap and water. After the fender is dry, a common protectant, suitable for vinyl or plastic, provides a nice finish. Properly inflated and cared for, Polyform fenders will provide years of excellent service.

How to Inflate a Polyform Fender with a Compressor - Videos

When you a purchase a Polyform fender, chances are they're going to come in a box like this. When you open that box, what you're going to something that looks like this, which is the fender. Now, it's not inflated. How in the world am I going to inflate this? When customers receive our fenders, normally the screw is halfway in. The screw has to be taken out, and it can be done either with a quarter or a screw driver. Put the screw driver into the screw, turn it counter-clockwise, and take it out. Most customers like to use an air nozzle to fill their product. When inflating the product, make sure that your air compressor is at 30 pounds of pressure or less. Stick the rubber nozzle into the product. How do we know how much air to put in this? All of our products should have 2 pounds of air pressure. Fill the product until you can push in a quarter of an inch on the side. Well once the product is inflated to two pounds of pressure, we need to put the valve screw back into the product. Make sure that we only go down to the face of the valve and no further in. You will feel resistance. Once you feel that resistance, stop. This is ready to go. All I need is a piece of line, which we call a fender rope, and this is ready to go on a boat.

How to Inflate a Polyform Fender with a Hand Pump - Videos

Using a Polyform Hand Pump to inflate a Polyform fender is very simple. First, using the proper-sized screw driver, remove the plug. Next, insert the pump nozzle and inflate. Do not over-inflate. The wall of the fender should be flexible. Finally, re-insert the plug. When the plug is flush with the surface, tighten until snug. The fender is now ready for use.